|
|
| Corporate |
|
Overview |
|
Mission |
|
News |
|
Employment |
Locations
 |
Angleton, TX |
 |
Austin, TX
|
 |
Concord, CA
|
 |
Dunseith, ND
|
 |
Fremont, CA
|
 |
New Hampshire |
 |
Huntsville (Brad), AL |
 |
Huntsville (HSI), AL
|
 |
Minnesota Division
|
 |
Tempe, AZ
|
 |
Guadalajara, Mexico
|
 |
Guaymas, Mexico
|
 |
Campinas, Brazil
|
|
|
Board of Directors |
|
|
|
Penang, Malaysia
Contact Information
Balamurugan Sinnasamy
Benchmark Electronics (M) Sdn Bhd
Free Industrial Zone, Phase 1
Bayan Lepas, Penang 11900
Malaysia
Tel. Number: 604-6441616
Fax Number: 604-6442033
Penang, Malaysia Facility
The Penang facility is located at the Bayan Lepas Free Industrial Zone,
Phase 1 and is approximately 2 km from the Penang International Airport.
The facility size is approximately 100,000 sq ft boasting a full supply chain
of back-up system manufacturing “wafer in, system out” capability. We have a
strong workforce of 465 employees, of which 50% of our indirect staff are technical-based
|
Square Footage:
|
103,000 square feet
|
| Market Segment
Serviced : |
- High End Computing
- Industrial Control
- Test & Measurement
- Medical
|
| Manufacturing Technologies: |
- MR head manufacturing and design (LTO, DLT, Travan)
- Tooling and automation development
- Box build assembly and test
- Robotics motion analysis
- Tape Drive signal processing
- Capable of product debug and improvement
- Process / Test Statistical Analysis (Softwares : Mathlab 2006, Minitab 14)
- Mechanical design
- Plastic injection components
- Metal machined and stamped components
- Backup interface device
- Design software (Pro-Engineer Wildfire 3)
|
| Manufacturing Lines: |
- 12 Box Build Lines (Heads, Drives & System)
- 2 PCBA Assembly Lines
|
| R&D Capability: |
- Mechanical / Electrical Design
- Software / Firmware Development
- Proto Build / NPI
- PCBA Layout
- Component Engineering
|
| Certifications: |
- MS ISO 9001 : 2000
- MS ISO 14001 : 2005
- OSHAS 18001 : 1999
- ISO 13485 (in progress)
- Agency Certification
- ESD Control Systems
- IEC61340-5-1 : 1998 (Compliant)
- ANSI/ESD S20.20 (2007)
- Workmanship Standards
- IPC-610A-D (Class 2&3) – Acceptability of PCBAs
- IPC-7711A/21A – Rework of PCBAs
|
| Other Services Offered: |
- Post Manufacturing Services
- Direct Order Fulfilment
- NPI Services
|
Driving Instructions to the Penang, Malaysia Facility
If taking a cab:
As you enter the main arrival hall, the taxi counter is on your right. Tell the receptionist
that you are going to Benchmark which is opposite Fairchild. She will give you a coupon when
you make payment. Once in the car, tell the driver again that you are heading to Benchmark,
opposite Fairchild.
Driving directions from the airport:
As you exit the airport, you will immediately come to a roundabout. You will see a signage
citing “Jalan Sultan Azlan Shah” at your left. Go up the ramp on your left. Down the road you
will see Benchmark on your right. Continue driving for another 400m where you will have to take
a U-turn. After the U-turn, keep left, and take the first left and immediately right. The
facility is less than a minute away.
| |
|
|
|